Types of Pneumatic Conveyors Systems

Pneumatic conveying systems can be classified on different basis of consideration. These basis are listed below:

  • On average particle concentration (modes)
  • On air pressure (Types of systems)
  • On air supply arrangement
  • On solid feeder type

Of these, the first two are very important and often influence the choice of the specific design for a given material, loading and delivery condition and the distance to be covered.

01-Pneumatic-Conveying System Plant - Coffee Conveyor Plant

Classification based on Average Particle Concentration – Modes of Conveying:

01-Dilute Phase - Dense Phase - Plug Phase - Conveying Of Particles

Depending on the mass flow ratio, defined as the ratio of mass of particles conveyed to the mass of fluid used to convey, pneumatic conveying system may be classified into two modes; namely

  1. Dilute phase
  2. Dense phase

01- Dilute Phase - Dense Phase - Conveying Ofgrain Particles In Vacuum Conveyor - Pneumatic Conveyor

If the mass flow ratio is low, the system is said to operate in dilute phase. Whereas, if the mass flow ratio is high, the system is said to operate in dense phase. If the mode of operation of a system is in dilute phase, the probable range of mass flow ratio is 0 – 15. The dense phase system operates at mass flow ratio over 15.

Read More:   Classification Of Material Handling Equipment | Types Of Material Handling Equipment Loads

In a dilute phase system the material is carried through the pipeline by a large volume of air having high velocity but relatively low pressure. The stream of air or gas carries the material in suspension in the pipeline as discrete particles owing to lift and drag forces acting on each particles. The distribution of particles over the cross section of the pipe is fairly uniform. In order to keep the particles in suspension, the air must possess a minimum velocity, called the pick up velocity. The pick up velocity for a particular material depends on many factors, like, the shape, size, specific weight of material and inclination of the pipeline.

01-Dilute Phase Pressure Conveying System

If the velocity of air is gradually lowered down below what is required to keep the particles in suspension, the particles gradually settle down and form dunes at the bottom of the pipeline all along the length of the pipe. In this condition the material is about to choke the pipeline and if the pressure is increased these dunes and plugs of materials may move along the pipeline causing a dense phase flow. In a dense phase flow usually the velocity of fluid is much lower than the minimum velocity required for a dilute  phase flow. The distribution of particles over the cross section of the pipe is non uniform. At the lower part of the pipe there is slow moving dunes or plugs of material and the upper part of the cross section of the pipe is filled with certain proportion of finer particles in suspension in a state of dilute phase.

Read More:   Material Handling Of Materials | 15 Surprising Stats About Material Handling System | The Ultimate Cheat Sheet on Material Handling Equipment

01-Dilute Phase Pressure Conveying System - Pneumatic Conveying System

01-Dense Phase Pneumatic Conveying System

The maximum mass flow ratio achievable for a dense phase flow depends on many factors like the nature of materials and air velocity. It is usually greater than 30

Classification based on Air Pressure:

Based on air pressure, Pneumatic conveying systems may be classified as follows:

  • Low pressure systems, in which the operating air pressure is about 1 atmosphere (760 mm Hg). This type of systems may be further sub classified into
  • Positive pressure system
  • Negative pressure system
  • Combined positive – negative pressure system
  • Medium pressure system
  • High pressure system

01- Pneumatic-Conveyor-Systems - Positive Conveying - Negative Conveying

Types of Pneumatic Conveyor | Vacuum and Positive Pressure Pneumatic Conveying Systems | Dense Phase Pneumatic Conveying System

  1. Avatar Of Tyler Johnson

    That’s good to know that you would be in the dense phase if you have optimal airflow. I would assume that you would want to be in the optimal phase for as long as possible then. I’ll keep that in mind if I decide to get some conveyors to help me out with grain processing on the farm I am thinking about starting

Leave a Reply